As an important bathroom product used to control the size of water flow and achieve water saving effects, a flat faucet can be used to control water flow, but it is unobstructed independently

When choosing faucets, more and more people are paying attention to quality, but there are many types of "all copper faucets", "maintainless steel faucets", "water saving faucets", "introduction faucets", and so on in the market The so called water saving faucet is not water saving at all When I bounce a beautiful designed faucet, I realized that it costs uld&# 039; T be installed All copper turned into half copper and half iron, and such incidents are not common

Seven common misconceptions when buying a faucet

Myth 1: Sending faucets to save water

Stainless steel faucet

Many consumers think that sensing faucets are conservative and save water, but in fact, sensing faucets not only have low water output, high prices, but also high maintenance costs. Induction faucets are generally installed and used in public places, office buildings, and government agencies But the use of sensing faucets in houses is not practical, and maintenance is time Consulting and laborious

Recruitment:

Not only sensing faucets can save water, but manual faucets also have water saving and energy saving measures Manual faucets not only have a long lifespan but are also easy to repair, making them relatively cost effective If you find it troublesome to switch, you can choose to install a press type faucet, Which is considered without turning and can achieve the water saving effect of timed water cut off The price is relatively cheap and cost effective

Myth 2: The smaller the flow rate, the more water saving it is

There is a water saving standard for the flow rate of the faucet, and both large and small flow rates are not conductive to water saving Many people have the misconception that a small flow faucet can save more water The water consumption is equal to the flow rate multiplied by the water usage time If the flow rate is too small, It will significantly promote the water usage time and not have a water saving effect Sometime the flow rate of the faucet is too low, which may be due to problems with the faucet valve or blockage of lag It should be cleaned or replaced in a timely Manner Thereforee, do not think that a low flow rate is better

Recruitment:

It is recommended to pay attention to the cleanliness of the faucet, clean and replace the faucet valve and filter screen in a timely manner, so as to maintain the cleanliness and hydrogen of the water and protect human health Water is the source of life, so it is related to the hydrogen of water We cannot single carelessness, And the hygiene of faucets is the foundation A clean and shiny appearance does not necessarily mean a clean interval

Myth 3: The bubble faucet saves water under any circulations

The water outlet of the faucet concerns of two parts: an external filter screen and an internal bubble The bubble&# 039; The main function is to increase the number of bubbles in the water and reduce the water output, so that the water does not splash and the flow rate is controlled, that achieving a certain water saving effect But not in all cases, failures with bubbles save water, weakening the impact of water flow and reducing the ability to wash and remove dirts There are more, when cleaning very dirty Things, It is necessary to use a large amount of water to clean, which is not conductive to water conservation

Recruitment:

When choosing a faucet with a bubble, it is important to pay attention to the installation position For washbases and kitchen sinks, consider installing a faucet with a bubble The floor mop pool installed on the balcony does not need to use a faucet with a bubble, which is not only increasing the speed of flushing the floor mop, but also increasing the flushing capacity, Achieving a certain water saving effect

Myth 4: The faucets have both hot and cold temperature adjustments

Faucets can be divided into several types based on their purpose, including base faucets, kitchen base faucets, bathtub faucets, washing machine faucets, and mop pool faucets Many consumers believe that as long as it is a faucet, it will have a cold and hot temperature adjustment function

Recruitment:

The cold and hot temperature regulation function of the faucet must have two inlet hosts and a ceramic valve core to achieve it. There are three types of faucets: base faucets, kitchen base faucets, and batch faucets available in either cold or single cooling mode, while washing machine faucets and mop pool faucets only have single cooling mode

Myth 5: Choosing a faucet without considering a base

A tabletop base is a type of tabletop base that is incrementally favored by people due to its near appearance and versatile design Many consumers, after installing a base on the table, do not notice that the base has come talker and still choose a regular base faucet; There is also a situation where the base only has one installation hole, but the consumer buys a dual control fault, and the result is that it cannot be installed

Recruitment:

The faucet needs to be installed on the basin, and the actual situation of the basin must be considered when purchasing If it is a base under the table or a column, choose a regular base faucet If it is a base on the table, choose a base faucet on the table (the height of the water outlet is higher than the edge of the base); If you prefer a dual handle dual control faucet, the base must have three installation holes

Myth 6: Hot and cold faucets can only be connected to one water pipe

As mentioned earlier, the cold and hot water faucet uses different opening angles on both sides of the ceramic valve core to control the mixing ratio of cold and hot water, there being learned water temperature regulation function But many people only find out when they buy it back that there is only one cold water pipe at home, thinking that connecting only one inlet hose can still work properly.

Recruitment:

The ceramic valve core is a three port interconnected structure. Under normal circumstances, two water inlet ports and one water outlet port mix, and the water from the two water inlet hoses flows out from the faucet outlet. When only one inlet hose is connected, there will be an inlet that becomes an outlet, and water will flow out from here, causing the faucet to malfunction and potentially flooding the golden mountains! If you only have one cold water pipe and buy a hot and cold faucet, you can connect two inlet hoses at the same time, then connect one to the corner valve, and use a plug to block the other.

Myth 7: The connection between the faucet and the water pipe does not require an angle valve

Many people know to install faucets, but they don't know to install angle valves. The outlet of the angle valve is at a 90 degree angle to the inlet, which can connect the inner wall water pipe with the faucet hose and control the water flow switch.

Recruitment:

All hot and cold faucets (with a hot and cold water inlet hose) need to be connected to the water pipe using an angle valve, while quick opening faucets such as washing machine faucets and mop pool faucets can be directly connected to the water pipe, so there is no need for an angle valve. Generally speaking, each hot and cold faucet requires two corner valves to be paired with it. In case of water leakage in the faucet, simply close the corner valve and it will not affect the water use in other parts of the home.

Article source: Kaiping faucethttp://drip-certified.com/