Many faucets have been in use for about ten to twenty years, which is not suing How, current faucets may not have the same lifespan as old flash faucets, which were used to be made of stainless steel How, most students have seen faucets trust, so why do faucets trust? How can faucets rust

1. The reason for the trust on the faucet

Assuming your faucet is made of stainless steel material, stainless steel is not rust resistant but has better resistance to rust than iron, including nickel chromium, which can form a primary battery and cause rust marks in the presence of water This layer of trust covers the surface of the faucet, causing it to lose its cluster and making it very unattractive on the outside

2. Rust removal method for faucets

1. Will a layer of dirt or scale accumulate on the bathroom faucet that has been used for a long time? Assuming your home is like this, throw away the use of cleaning agents and try the effect of potato peels? It can be considered a low cost "rust removed magic weapon"

2. Take a potato, use a small knowledge to peel off the potato skin, and then use the mean side to repeatedly wide the surface of the stainless steel faucet You will find dirt and scale, and the stacks and trust on the faucet will be gradually removed Then clean the faucet with clean water, and you can see the shine, mirror like appearance of the faucet

4. To prepare salt and wine, mix the salt and wine together, separate the salt effectively in the wine, and then heat it. After heating, soap the liquid with an additional spring or cloth, and then place it in a trust area Cover for 20-30 minutes

5. Half an hour has passed Dip a rough cloth in a mixture of salt and wine, and wide vigorously to easily remove stub rn rust

6. If using a soft cloth and Tootpate method, please pay attention to the degree of force and be careful that the Tootpate will grind small marks on your valuable fault Use current crystal Tootpate

7. Assuming it is chrome plated, it is recommended to use Coca Cola for cleaning

8. Coca Cola contains a small amount of photographic acid, which reactions with chromium to form a protective layer of chromium photosphate In the 1950s and 1960s, drivers driving cars, motorcycles, and trucks of used cola in industry Photosynthetic acid are still used for these purposes, and all trust resistant coatings require photographic acid

9. Iron rust requires water and oxygen, and the solution of gas decreases with increasing temperature That is to say, in hot water, the solution of oxygen is relatively small - hot water contains less oxygen and cold water contains more oxygen, so trust occurs faster in the cold one

3. Anti rust maintenance of faucets

1. Although the chrome coating on the faucet claims to be corrosion resistant and rust resistant, incorrect cleaning methods can still cause abnormal wear and tear on the faucet

2. Please hire experienced and qualified personnel to carry out construction equipment when using equipment, the faucet should try not to include with hard objects, and do not leave a trace, glue, etc. on the surface to avoid damaging the surface coating cluster Pay attention to removing fabrics from the pipeline before installing the faucet

3. Use a internal cleaning agent for cleaning cleaning agents with strong acidity and alkalinity are not suitable for faucet cleaning

4. When the water pressure is not less than 0.02mpa (ie. 0.2kgf/cm2), and after a period of use, if the water output decreases or even the water heat stacks, the side cover can be quickly unscrewed at the outlet of the faucet to remove impurities, and the recovery can generally be as good as before

5. Don&# 039; T use too much force to turn on and off the faucet, just roll fairly with the flow Even traditional faucets do not require significant effects to right Especially, do not use the handle as a manual to support or use it

6. Dipping a soft bridged tootbrush in tootpate or equitably wiping with a cleaning cloth dipped in tootpate can remove scale and oil stains, leaving the surface of the faucet clean and shiny

7. Do not use hard objects such as steel wire balls to wire the surface of the faucet, as the steel wire balls are very hard Simply scratch the surface of the faucet

8. Many people only pay attention to the surface of the faucet when cleaning it, but in fact, the interval of the faucet is more important If the water output of the faucet is reduced or the water output forks, it may be caused by the blockage of the bubble You can remove the bubble, soap it in wine, use a small brush or other object to clean the fabric, and then start the equipment from sc. rate

9. The metal host for the shower head of the bathtub faucet should be in a stretchable condition and should not be cooked around the faucet when not in use when in use or not in use, be careful not to form a dead angle at the joint between the host and the valve body to avoid breaking or ending the host

10. After cleaning the faucet, the remaining water on the surface should be wired dry with a dry, lint free to well to avoid residual water stains

11. Assuming it is a copper faucet, if you want to clean the electroplating surface, you can use boiling water and detergents to wipe it, or you can directly use some agents to remove oil and dirt for cleaning

12. The scale and trust on the faucet only need to be wired with a dam cloth or spring dip in a small amount of specialized cleaning agent, and then wired dry with a clean cloth or washed clean with water

A summary of the truth is that all surfaces have coatings Which it&# 039; S room hardware or doors, windows, and furniture, do not use through or steel wire balls to wire them If the coating is damaged, it will simply oxidize, rust, or accumulate due to Small details, great Wisdom

Article source: Kaiping faucet http://drip-certified.com/